R2D2 1:1 Parts

PLEASE NOTE:  All parts are Builders Club approved and have been for some time now after going through the process of submitting pictures and documentation, proving I made all the parts myself and to the correct specification. 



All parts I make are made to the specified 1:1 dimensions as laid down for all builders in the CS:L version, but since starting to build my R6, I found many of the parts were chunkier than they needed to be with lots of excess resin that served no purpose. So I set about streamlining the parts to shave off as much weight as possible without affecting the cosmetic side or strength of them.

 All parts are now made from a brand new eco friendly industrial grade polyurethane resin, which means they are not only lighter, but stronger and more durable too.

    26 product(s) found for "R2D2 1:1 Parts"
  • R2 Ankle Cylinder Holders
    R2 Ankle Cylinder Holders
    £6.25
    This is for a pair of Cylinder Holders, enough to do either the outer legs or inner one, and if you want to do both you will need two packs of these. These I hollowed out a recess in the back to save a bit of extra weight, and it can still be stuck on as per the original one. All parts come in beige resin ready for you to paint.
    Details
  • R2 Ankle Cylinder Wedges
    R2 Ankle Cylinder Wedges
    £2.50
    This is for a pair of Ankle cylinder wedges, enough to do either the outer legs or inner one, and if you want to do all three legs then you will need two packs of these. This is one of the smaller, but still chunky parts as I classed it, in that it was just a chunk of resin that didn't need to be and was just dead weight, so I hollowed out a recess in the back to save a bit of extra weight, while leaving enough so it can still be stuck on as per the original one. All parts come in beige resin ready...
    Details
  • R2 Ankle Cylinders
    R2 Ankle Cylinders
    £17.50
    This is for a pair of Ankle cylinders, enough to do either the outer legs or inner one, and if you want to do all three legs then you will need two packs of these. This was just one big chunk of resin, and even my new lightened version is still the heaviest part I make, but I have hollowed out a series of recesses in the back to save as much weight as I could, while leaving enough so it can still be fixed on as per the original ones. All parts come in beige resin ready for you to paint.
    Details
  • R2 Ankle Detail Pieces
    R2 Ankle Detail Pieces
    £12.50
    These are the ankle detail parts which fit on the front and back of the ankle and come in a set of four, enough to do one droid. This part I lighten by removing most of the unseen bulk at the back, leaving just a framework and two fixing points. All parts come in beige resin ready for you to paint.
    Details
  • R2 Battery Harness
    R2 Battery Harness
    £12.50
    This is for a set of four Battery Harnesses enough to do one droid. There wasn't any weight saving to be had on this part, but instead of casting it in fiddly little bits like I have seen, I set about making and casting it as one, so it just fits straight on. All parts come in beige resin ready for you to paint.
    Details
  • R2 Charging Arm
    R2 Charging Arm
    £15.00
    This is what I call one of my made parts, in that there was no official plans for this at the time I made it, just spotted it in the DK star wars book and thought it would look quite good, so set about scaling and making it. I have now remade it, so the main head part is injection moulded which means the finish is better and its far more durable, plus the old plastic tube has been replaced with an aluminium one. You will receive this pre assembled with a few smaller lose bits, but nothing is glued...
    Details
  • R2 Coin Slot Strip
    R2 Coin Slot Strip
    £5.00
    This is the strip of coin slots that go on the front, and due to the design there isn't a whole lot that can be removed, but I took away small amounts between the slots which is not seen and also opened the coin slots up so they now go right through, and to aid fixing added six small holes to help you attach it. All parts come in beige resin ready for you to paint.
    Details
  • R2 Front Logic Surrounds
    R2 Front Logic Surrounds
    £2.50
    This is for a pair of front logic surrounds enough to do one droid. This part there isn't a whole lot that can be removed, but I bevelled edge at either end to allow them to fit better against the inside of the dome but still retain the wider back edge for attaching a light boards to, and they now have a slight radius so when you look at the logic surrounds from the outside the protruding edge looks more even to the shape of the dome. All parts come in beige resin ready for you to paint .
    Details
  • R2 Front Vents
    R2 Front Vents
    £16.00
    This is for a PAIR of front vents, one for the top, and one for the bottom, as they are both different. This is another one of those chunky parts that had a lot of excess resin at the back which didn't need to be and was only there to make open casting easier, so I removed the access bulk from the back and close cast them All parts come in beige resin ready for you to paint.
    Details
  • R2 Halfmoon Detail plates
    R2 Halfmoon Detail plates
    £15.00
    This is for a pair of Halfmoon detail plates, enough to do either the outer legs or inner one, and if you want to do both you will need two packs of these This part I lighten by removing most of the unseen bulk at the back, leaving just a framework and two fixing points. All parts come in beige resin ready for you to paint.
    Details
  • R2 Holo Projector Set
    R2 Holo Projector Set
    £16.00
    This is for a set of three holo projectors. One movable and two fixed both at different angles. It also includes self adhesive felt strip to allow the movable one to move smoothly, and vac formed clear lenses. While this looks the same as the old ones it's been lightened and modified out of sight so to speak. For starters the unseen resin from behind has been removed, allowing easier fitment of a light source as there is now more room, and the lip around the fixing rings has been reduced as I found...
    Details
  • R2 Knurled Hose Fittings
    R2 Knurled Hose Fittings
    £3.75
    All said and done on this part there isn't really anything that can be removed excess resin wise, so it's just as standard but in the new resin This is for 8 hose fittings, enough to do one droid, and come in beige resin ready for you to paint.
    Details
  • R2 Large Data Port
    R2 Large Data Port
    £11.25
    This is for a single Large Date Port, enough to do one droid, just as per the specs. All parts come in beige resin ready for you to paint.
    Details
  • R2 Leg Struts
    R2 Leg Struts
    £16.00
    This is for a pair of Leg Struts , enough to do one droid. This part is now cast in two pieces, the main body and the tubes, which are now aluminium with resin inserts oppose to solid resin. Parts come in beige resin and bare aluminium ready for you to paint.
    Details
  • R2 Motivator
    R2 Motivator
    £10.00
    This is my new version motivator, which with a combination of my chums 4k tv and my blue ray disk the detail is clearer, (not perfect, but much better) so I set about updating my old version to more like the clearer image. First what I thought were nuts or screws in the top turned out to be little spike like protrusions, and the sides of the top were not smooth, but clear had ribs around it. The detail of the lower section is still hazy, but there is what looks like a circuit board with coil on onside...
    Details
  • R2 Octagon Ports
    R2 Octagon Ports
    £10.00
    This part is made to the specified 1:1 dimensions, however I based the slat spacing and centre knob size more on the original pictures of ILM's uber droid as it was called, as personally I thought the slighter bigger slats looked better, but all said and done most people never spot the difference. These now come with see through slats as some people like to leave them open, but on the other hand if you want to close them up, it's much easier to paint a piece of plastic blue to go behind, then stick...
    Details
  • R2 Power Couplings
    R2 Power Couplings
    £16.00
    This is for a PAIR of Power Couplings enough to do one droid, as in one for the front and one the back. This is another one of those chunky parts that had a lot of excess resin at the back which didn't need to be and was only there to make open casting easier, so I removed the access bulk from the back and close cast them All parts come in beige resin ready for you to paint.
    Details
  • R2 Radar Eye
    R2 Radar Eye
    £15.00
    This part I lighten by removing most of the unseen bulk at the back, leaving just a framework and four fixing points. This is for one radar eye and it comes complete with a black eye lens Main part come in beige resin ready for you to paint.
    Details
  • R2 Rear Logic Surround
    R2 Rear Logic Surround
    £3.75
    This is for one rear logic surround, enough to do one droid. This part there isn't a whole lot that can be removed, but I shaved a few grams off while adding a fixing hole at either end. All parts come in beige resin ready for you to paint.
    Details
  • R2 Restraining Bolt C3-PO
    R2 Restraining Bolt C3-PO
    £5.00
    This part is the restraining bolt as seen on C3P0 in Star wars, (just outside the Jawa sandcrawler) and with more detail now visible in blu ray, it made the making of this part much easier. Its hollow cast and comes fitted with a high power magnet to allow you to place a piece of metal or another magnet on the back of your droid or costume to allow the easy placement and removal of this as per seen in the film. While its the one seen on C3P0 there is no reason why you can't put it on your R2 if you...
    Details
  • R2 Restraining Bolt R2-D2
    R2 Restraining Bolt R2-D2
    £5.00
    I made this part from a picture on the extras disc of the blu ray dvd set where there is a really good close up of this attached to R2, and clearly show all the finer details previously people were unsure about. Its hollow cast and comes fitted with a high power magnet to allow you to place a piece of metal or another magnet on the back of your droid or costume to allow the easy placement and removal of this, as per seen in the film. All parts come in beige resin ready for you to paint.
    Details
  • R2 Shoulder buttons
    R2 Shoulder buttons
    £2.50
    This is for a set of four shoulder buttons, enough to do one droid, and come in beige resin ready for you to paint. These are a lightweight version I done by simply hollowed the back out, but in doing so halved their weight, and these with a hollow back are intended to be glued in place. All parts come in beige resin ready for you to paint.
    Details
  • R2 Shoulder Hubs
    R2 Shoulder Hubs
    £15.00
    This is for a pair of shoulder hubs, enough to do one droid. This part I lighten by removing some of the unseen bulk at the back, while leaving the option to either glue in place, or use the three magnet twist and hold system to allow access to the shoulder mountings. All parts come in beige resin ready for you to paint.
    Details
  • R2 Shoulder Hydraulics
    R2 Shoulder Hydraulics
    £5.00
    This is for a set of two shoulder Hydraulics enough to do one droid This part there wasn't anything to be removed weight wise, but as the old mould had worn out, a new mould was made to use my new resin so the part is now stronger and more durable. All parts come in beige resin ready for you to paint.
    Details
  • R2 Shoulder Stabiliser
    R2 Shoulder Stabiliser
    £6.25
    On this part there isn't anything to remove weight wise, so they come just as per the official plans. This is for a set of four shoulder stabiliser's, enough to do one droid, and come in beige resin ready for you to paint.
    Details
  • R2 Utility Arms
    R2 Utility Arms
    £17.50
    While these look the same from the front, I have been listening to other builders and their gripes if you like and tried my best to sort these out. First of all there is the end snapping off near the narrow part when at shows etc, where kiddies pull on them, (can't be helped,) so to that end these were purposely designed using the latest computer software to be made from resin, not a copy of an aluminium one, but I started fresh and not only lightened them, but made them more durable too. Next I...
    Details
Product Added to your Cart
x

-------- OR --------